Brocade 6910 Ethernet Access Switch Configuration Guide (S Manuel d'utilisateur Page 51
- Page / 124
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Brocade 6910 Ethernet Access Switch Configuration Guide xlix
53-1002651-02
About This Document
In this chapter
•Supported hardware and software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . xlix
•Summary of enhancements for Brocade R2.2.0.2 . . . . . . . . . . . . . . . . . . . . . . l
•Summary of enhancements for Brocade R2.2.0.0 . . . . . . . . . . . . . . . . . . . . . . l
•Summary of enhancements for Brocade R2.1.0.4 . . . . . . . . . . . . . . . . . . . . . li
•Summary of enhancements for Brocade R2.0.2.10 . . . . . . . . . . . . . . . . . . . . li
•Summary of enhancements for Brocade R2.0.2.9 . . . . . . . . . . . . . . . . . . . . . lii
•Document conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . lii
•Trademark references . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . liii
•Related publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . liv
•Getting technical help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . liv
•Document feedback . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . liv
Supported hardware and software
This guide describes the Brocade 6910 Ethernet Access Switch 2.2.0.2 release.
The following hardware platforms are supported by the release of this guide:
• BR-6910-EAS-AC – Brocade 6910 Ethernet Access Switch, 12×1 GbE combination copper
10/100/1000 Base-T (RJ45) or 100/1000 Base-X SFP ports, redundant AC power supply
• BR-6910-EAS-DC – Brocade 6910 Ethernet Access Switch, 12×1 GbE combination copper
10/100/1000 Base-T (RJ45) or 100/1000 Base-X SFP ports, redundant DC power supply
• BR-6910-EAS-H-AC – Brocade 6910 Ethernet Access Switch, 12×1 GbE combination copper
10/100/1000 Base-T (RJ45) or 100/1000 Base-X SFP ports, redundant AC power supply,
temperature hardened
• BR-6910-EAS-H-DC – Brocade 6910 Ethernet Access Switch, 12×1 GbE combination copper
10/100/1000 Base-T (RJ45) or 100/1000 Base-X SFP ports, redundant DC power supply,
temperature hardened
- Brocade 6910 1
- Ethernet Access Switch 1
- Document History 2
- Contents 5
- Chapter 4 General Commands 6
- Chapter 6 SNMP Commands 8
- 53-1002651-02 10
- Chapter 12 Interface Commands 13
- Chapter 19 ERPS Commands 16
- Chapter 20 VLAN Commands 16
- Chapter 24 LLDP Commands 20
- Chapter 25 CFM Commands 20
- Chapter 26 OAM Commands 22
- Chapter 28 DHCP Commands 22
- Section III Web Configuration 24
- Chapter 35 VLAN Configuration 25
- Chapter 38 Congestion Control 26
- Chapter 39 Class of Service 26
- Chapter 42 Security Measures 27
- Chapter 44 IP Configuration 29
- Chapter 45 General IP Routing 30
- Chapter 46 IP Services 30
- Section IV Appendices 31
- About This Document 51
- Enhancement Description 52
- Document conventions 54
- Trademark references 55
- Related publications 56
- Getting technical help 56
- Document feedback 56
- Getting Started 57
- 1Introduction 59
- Feature Description 60
- System Defaults 64
- System Defaults (Continued) 65
- 2Initial Switch Configuration 67
- Required Connections 68
- Basic Configuration 69
- Setting Passwords 70
- Setting an IP Address 70
- • IP address for the switch 71
- • Prefix for this network 72
- Dynamic Configuration 73
- Trap Receivers 78
- Command Line Interface 81
- Accessing the CLI 83
- Entering Commands 84
- Minimum Abbreviation 85
- Command Completion 85
- Getting Help on Commands 85
- Partial Keyword Lookup 87
- Using Command History 87
- Understanding Command Modes 88
- Exec Commands 88
- Configuration Commands 89
- Command Line Processing 90
- CLI Command Groups 91
- 4General Commands 95
- Console(config)#prompt RD2 96
- RD2(config)# 96
- General Commands 102
- 5System Management Commands 103
- Banner Information 104
- Command Function Mode 105
- Console(config)# 107
- System Status 113
- Frame Size 121
- File Management 121
- Column Heading Description 127
- TABLE 17 Line Commands 131
- Console(config)#line console 132
- Console(config-line)# 132
- Console#disconnect 1 138
- Console# 138
- Event Logging 139
- TABLE 19 Logging Levels 141
- Console(config)#logging on 142
- Console#clear log 143
- SMTP Alerts 145
- TABLE 23 Time Commands 149
- Console#show sntp 151
- Example 153
- Console#show calendar 156
- 15:12:34 February 1 2011 156
- Time Range 157
- Console(config-time-range)# 158
- 6SNMP Commands 161
- SNMP Commands 162
- SNMP Commands (Continued) 162
- 1. No view is defined 170
- 2. Maps to the defaultview 170
- Console(config)#nlm A1 177
- 7Remote Monitoring Commands 181
- Remote Monitoring Commands 187
- 8Flow Sampling Commands 189
- Console(config)#sflow 190
- Console(config-if)# 190
- 9Authentication Commands 195
- Authentication Sequence 198
- RADIUS Client 200
- TACACS+ Client 204
- TABLE 39 AAA Commands 207
- Console(config-sg-radius)# 211
- Web Server 215
- Web Browser Operating System 217
- Telnet Server 218
- Secure Shell 220
- Console#configure 223
- Console(config)#ip ssh server 223
- 802.1X Port Authentication 228
- Console#dot1x re-authenticate 236
- Management IP Filter 242
- 10General Security Measures 245
- Console#show port security 247
- Web Authentication 262
- DHCP Snooping 267
- IP Source Guard 276
- ARP Inspection 281
- 11Access Control Lists 289
- Console(config-std-acl)# 290
- Console(config-ext-acl)# 293
- IPv6 ACLs 296
- Console(config-std-ipv6-acl)# 297
- next-header] 298
- MAC ACLs 301
- Console(config-mac-acl)# 304
- ARP ACLs 305
- Console(config-arp-acl)# 306
- ACL Information 308
- 12Interface Commands 311
- Interface Commands 329
- Console(config-if)#power-save 338
- Power Saving Status: 339
- Ethernet 1/10 : Enabled 339
- 13Link Aggregation Commands 341
- Link Aggregation Commands 350
- 14Port Mirroring Commands 353
- RSPAN Mirroring Commands 356
- 15Rate Limit Commands 363
- Rate Limit Commands 364
- Related Command 364
- In this chapter 365
- 17Address Table Commands 379
- • Config - Static entry 381
- Address Table Commands 383
- Command Mode 383
- Privileged Exec 383
- 18Spanning Tree Commands 385
- Console(config)#spanning-tree 387
- • Spanning Tree Protocol 389
- Console(config-mstp)# 392
- Spanning Tree Commands 410
- 19ERPS Commands 411
- Console(config)#erps 412
- Console(config-erps)# 413
- ERPS Commands 423
- 20VLAN Commands 425
- • leave >= (3 x join) 427
- • leaveall > leave 427
- Editing VLAN Groups 430
- Console(config)#vlan database 431
- Console(config-vlan)# 431
- Configuring VLAN Interfaces 433
- Displaying VLAN Information 440
- Switch C 444
- Switch B 444
- Switch A 444
- Configuring L2CP Tunneling 447
- Console(config-)# 449
- Configuring VLAN Translation 450
- (VLAN 10) (VLAN 100) 451
- (VLAN 100) 451
- (VLAN 10) 451
- Configuring IP Subnet VLANs 459
- Configuring MAC Based VLANs 462
- Configuring Voice VLANs 464
- 21Class of Service Commands 471
- DEFAULT SETTING 476
- 22Quality of Service Commands 483
- Console(config-pmap-c)# 492
- Multicast Filtering Commands 499
- IGMP Snooping 500
- Static Multicast Routing 519
- IGMP Filtering and Throttling 520
- Console(config-igmp-profile)# 521
- MVR for IPv4 526
- Console(config)#mvr domain 1 528
- Console(config)#mvr 532
- MVR for IPv6 541
- Console(config)#mvr6 domain 1 543
- 24LLDP Commands 555
- refresh-interval 559
- LLDP Commands 567
- 25CFM Commands 573
- CFM Commands 574
- CFM Commands (Continued) 574
- Console(config-ether-cfm)# 581
- 26OAM Commands 625
- Console(config-if)#efm oam 626
- Domain Name Service Commands 635
- 28DHCP Commands 643
- DHCP Relay 648
- 29IP Interface Commands 651
- Basic IPv4 Configuration 652
- IPv4 Interface 655
- ARP Configuration 658
- Console#clear arp-cache 660
- Console#show arp 660
- IPv6 Interface 661
- Console#clear ipv6 neighbors 682
- Related Commands 684
- 30IP Routing Commands 685
- IP Routing Commands 688
- 31Debug Commands 689
- Debug Commands 692
- 0300005C)> 694
- Web Configuration 709
- 32Using the Web Interface 711
- Home Page 712
- Configuration Options 713
- Panel Display 713
- Main Menu 714
- Switch Main Menu (Continued) 715
- 33Basic Management Tasks 731
- FIGURE 10 System Information 732
- Managing System Files 735
- • “copy” on page 67 737
- Setting The Start-Up File 738
- Showing System Files 739
- Setting the System Clock 743
- • “Time” on page 93 744
- Specifying SNTP Time Servers 745
- Setting the Time Zone 746
- Australia 747
- Configuring the Console Port 749
- Configuring Telnet Settings 750
- Displaying CPU Utilization 752
- Displaying Memory Utilization 752
- Resetting the System 753
- Restarting the Switch (In) 755
- Restarting the Switch (At) 756
- 34Interface Configuration 757
- Configuring by Port Range 759
- Displaying Connection Status 760
- • Configuration Guidelines 763
- TABLE 155 Port Statistics 767
- Port Configuration 768
- Port Statistics (Continued) 768
- Parameter Description 769
- Configuring History Sampling 771
- Displaying Transceiver Data 774
- Performing Cable Diagnostics 777
- Performing Loopback Testing 778
- Trunk Configuration 781
- Configuring a Static Trunk 782
- Configuring a Dynamic Trunk 784
- Displaying LACP Port Counters 789
- • “show lacp” on page 293 790
- Configuring Load Balancing 793
- Saving Power 795
- Sampling Traffic Flows 796
- Traffic Segmentation 799
- VLAN Trunking 802
- 35VLAN Configuration 805
- • Priority tagging 806
- FIGURE 80 Using GVRP 807
- Configuring VLAN Groups 808
- IEEE 802.1Q Tunneling 816
- • Untagged 818
- • One tag (CVLAN or SPVLAN) 818
- • Double tag (CVLAN + SPVLAN) 818
- Protocol VLANs 823
- Configuring MAC-based VLANs 830
- Configuring VLAN Mirroring 831
- 36Address Table Settings 835
- Changing the Aging Time 837
- 37Spanning Tree Algorithm 841
- Region R 842
- FIGURE 127 STA Port Roles 854
- 38Congestion Control 863
- Storm Control 864
- Automatic Traffic Control 866
- Setting the ATC Timers 867
- 39Class of Service 871
- Selecting the Queue Mode 872
- Layer 2 Queue Settings 874
- Setting the Queue Mode (WRR) 874
- Priority Level Traffic Type 875
- • Port – Specifies a port 876
- Layer 3/4 Priority Settings 877
- 40Quality of Service 883
- Configuring a Class Map 884
- FIGURE 155 Showing Class Maps 885
- Creating QoS Policies 887
- 41VoIP Traffic Configuration 897
- Configuring Telephony OUI 899
- 42Security Measures 903
- Configuring AAA Accounting 910
- Configuring AAA Authorization 914
- Configuring User Accounts 916
- Configuring HTTPS 928
- FIGURE 194 Configuring HTTPS 929
- Console#reload 930
- Configuring Secure Shell 931
- Configuring the SSH Server 933
- Generating the Host Key Pair 934
- Importing User Public Keys 936
- Access Control Lists 938
- Setting A Time Range 939
- Showing TCAM Utilization 941
- Setting the ACL Name and Type 942
- FIGURE 206 Creating an ACL 943
- • 32 (urg) – Urgent pointer 946
- Configuring a MAC ACL 950
- Configuring an ARP ACL 952
- Configuring ACL Mirroring 954
- • Port – Port identifier 955
- Showing ACL Hardware Counters 956
- Configuring Port Security 965
- Displaying 802.1X Statistics 975
- DHCP Snooping Configuration 983
- Configuring Event Logging 989
- • “Event Logging” on page 83 990
- Remote Log Configuration 992
- Transmission Interval 995
- • “LLDP Commands” on page 499 996
- ID Basis Reference 998
- TABLE 175 Port ID Subtype 1001
- Bit Capability 1002
- Link Layer Discovery Protocol 1004
- Displaying Device Statistics 1006
- • Link-up and Link-down Traps 1009
- • “snmp-server” on page 107 1009
- • Authentication Traps 1009
- Setting the Local Engine ID 1010
- Specifying a Remote Engine ID 1011
- Setting SNMPv3 Views 1012
- FIGURE 257 Showing SNMP Views 1013
- Configuring SNMPv3 Groups 1015
- Specifying Trap Managers 1021
- Showing SNMP Statistics 1027
- Remote Monitoring 1029
- Configuring RMON Events 1032
- ERPS Global Configuration 1040
- ERPS Ring Configuration 1041
- Creating an ERPS Ring 1045
- Connectivity Fault Management 1048
- • “CFM Commands” on page 517 1051
- Associations") 1052
- Defect Description 1056
- Displaying Local MEPs 1082
- Displaying Local MIPs 1085
- Displaying Remote MEPs 1086
- OAM Configuration 1094
- State Description 1095
- Displaying the OAM Event Log 1098
- 44IP Configuration 1103
- Configuring an IPv6 Address 1111
- Showing IPv6 Addresses 1113
- Field Description 1115
- Showing IPv6 Statistics 1116
- Parameters 1117
- Showing IPv6 Statistics (UDP) 1121
- Using the Ping Function 1122
- • “traceroute” on page 600 1124
- Address Resolution Protocol 1125
- Basic ARP Configuration 1126
- • “arp” on page 602 1127
- Displaying ARP Entries 1129
- Displaying ARP Statistics 1130
- 45General IP Routing 1131
- IP Routing and Switching 1132
- Configuring Static Routes 1134
- Displaying the Routing Table 1135
- 46IP Services 1137
- • “show dns” on page 585 1139
- • “ip host” on page 582 1140
- • “show hosts” on page 586 1140
- Displaying the DNS Cache 1142
- Provides IP address 1144
- 47Multicast Filtering 1147
- • “IGMP Snooping” on page 443 1149
- FIGURE 389 MVR Concept 1170
- • “MVR for IPv4” on page 470 1173
- Displaying MVR Statistics 1180
- • “MVR for IPv6” on page 485 1186
- Displaying MVR6 Statistics 1193
- Appendices 1197
- ATroubleshooting 1199
- Using System Logs 1200
- BSoftware Specifications 1201
- Management Features 1202
- Standards 1203
- Management Information Bases 1204
- CLicense Information 1207
- DGlossary and Acronyms 1213
- Command List 1221
- Numerics 1229
Produits connexes et manuels pour Accessoires pour ordinateurs Brocade 6910 Ethernet Access Switch Configuration Guide (S
Accessoires pour ordinateurs Brocade Multi-Service IronWare Multicast Configuration Gui Manuel d'utilisateur
(216 pages)
(216 pages)
Accessoires pour ordinateurs Brocade NetIron CER 2000 Series Hardware Guide (Supporting Manuel d'utilisateur
(110 pages)
(110 pages)
Accessoires pour ordinateurs Brocade Multi-Service IronWare Routing Configuration Guide Manuel d'utilisateur
(846 pages)
(846 pages)
Accessoires pour ordinateurs Brocade ICX 6610 Stackable Switch Hardware Installation Gu Manuel d'utilisateur
(108 pages)
(108 pages)
Accessoires pour ordinateurs Brocade ICX 6450 Stackable Switches Hardware Installation Manuel d'utilisateur
(116 pages)
(116 pages)
Accessoires pour ordinateurs Brocade Multi-Service IronWare Administration Guide (Suppo Manuel d'utilisateur
(432 pages)
(432 pages)
Accessoires pour ordinateurs Brocade Multi-Service IronWare Multiprotocol Label Switch Manuel d'utilisateur
(852 pages)
(852 pages)
Accessoires pour ordinateurs Brocade FastIron WS Hardware Installation Guide Manuel d'utilisateur
(74 pages)
(74 pages)
Accessoires pour ordinateurs Brocade FastIron SX Series Chassis Hardware Installation G Manuel d'utilisateur
(192 pages)
(192 pages)
Accessoires pour ordinateurs Brocade Unified IP MIB Reference (Supporting FastIron Rele Manuel d'utilisateur
(768 pages)
(768 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.057 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels